Community

Can we migrate VM from VMware to Azure Stack HCI/ Azure Local using VBR?Is the steps same with migrating VMware to Hyper-V?

I have one job that started failing to create synthetic fulls on weekends.   The job runs just fine M-F creating incremental backups. I have another job that also creates synthetic full backups over the weekend.  And that job finishes with no errors.  So I know it’s not my NAS (Qnap) that is having issues.So why is it doing this for only the one job?   Error log below. 02.02.2025 16:57:48.444]    <43>   Error (3)    Failed to execute full transform task[02.02.2025 16:57:48.444]    <43>   Error (3)    Agent: Failed to process method {Transform.CompileFIB}: The semaphore timeout period has expired.[02.02.2025 16:57:48.444]    <43>   Error (3)    Asynchronous request operation has failed. [requestsize = 700416] [offset = 1242582327296][02.02.2025 16:57:48.444]    <43>   Error (3)    The semaphore timeout period has expired.[02.02.2025 16:57:48.444]    <43>   Error (3)    Asynchronous request operation has failed. [requestsize = 540672] [offset = 1242583027712

In a world where cyberattacks are becoming increasingly sophisticated, trust in our backups has become a constant concern. Is having immutable backups enough? Is storing them offline sufficient? The reality is that while these are good practices, attackers have evolved and now seek to compromise not only production environments but also backup systems. Therefore, backup security should not be seen as a fixed state but as an ongoing process.Aware of this challenge, Veeam® Software and Sophos have joined forces in a strategic partnership to take backup security to the next level.A Partnership to Protect Critical BackupsOn October 24, 2023, Veeam and Sophos announced their collaboration to enhance enterprise cyber resilience. This integration combines the Veeam Data Platform with Sophos Managed Detection and Response (MDR), providing an additional layer of managed detection and response to protect backups from ransomware attacks.This partnership enables:Real-time threat detection, monitor

I would like to verify the data in my backup copy job from my Veeam Backup for Microsoft 365 however I cannot find a place where I can select restoring from the copy job instead of the backup job itself. Is it possible to select the data to be restore from the Backup Copy Job?

I’ve been using Veeam for a while now. I was under the impression that I was performing a full backup every week. The way I have been doing this is I have 4 USB hard drives which I rotate. I plug one in on a Friday, wipe it, it backs up over the weekend (no errors), then Monday I unplug it. Friday I plug in the next one and repeat the process.I’ve just had need to restore from a backup, I wanted to restore the entire VM, and it’s errored saying the .vib file is missing. Having had a Google, everything seems to say this is a file for incrementals. Have I rendered all my backups useless up to this point by wiping the disk each week? The backup files it is creating are always a similar size to the VM I’m backing up so I’d assumed it was indeed “Full”. Is there anything I can do to restore my back up, and which setting have I missed in the backup job to make it do actual, proper, full backups?Thank youStuart

Hello,I am looking to recover some files of interest that were backed up to tape over a year ago.  The files were on a Hyper V VM running windows server.  The files were part of a backup job that was run on VEEAM at that time.  I obtained the tapes and imported the entire tape job to our backup server, which is a 5 tape media set around 50 TB.  When I attempt to "Restore guest files" from the imported tape, I get an error message that some of the files are missing and then get the following errors, indicating that "Mount wasn't found".  Of note, the previous backup/tape job was on a different domain that has been since decommissioned, so we are now running our backups under a new domain controller.  Would the old domain be the mount it is looking for?  I'm wondering if it is unable to mount because it is trying to do so on the old domain (which doesn't exist)?  Of note, I utilized the same process in the past to recover files on tape with no issue, but that was on the previous domain. 

I have a lot of jobs that are getting a new naming convention. The old way to do this was remove from the job from the configuration, modify the folder name on the repository, rename the job, rescan the Repo, then map the back files to the job.   I found there is an updated way to do this and is a welcome feature to save time. To go one step further, it is not recommended to use the remove/rescan method due to the fact the files get new identifiers that cause the restore points to be seen as new data by all tape and cloud storage offload jobs.  To test it, lets create a new job.In my case it’s called “___TEST_NAME_CHANGE” to keep it at the top of my screen.  Next, after running a job, we will click “Disk” on the left to make sure there is a backup on the Repository. It’s similar, but it’s not quite the same screen. 😉  Now, return to the Backup page, right click your Backup job, click edit, and lets rename it.   On the Backup Job page you can see it’s been renamed.   On the Disk page w

Sizing for NAS/file share backup can appear difficult initially, but with the help of the unofficial NAS Calculator by Hal Yaman it definitely will be a bit easier.As you can see from the screenshot below you need to know roughly how much source data in TB your file share(s) contain, how many files and directories. In case you are wondering what is primary vs secondary repository? Primary is for your short term retention (newest version) and secondary is for long term retention (older versions than newest).The user guide has some good info on the secondary copy settings.Once you have filled all out, just click the Calculate button to get full sizing for all components:Cache repository File Proxy Primary repository Secondary RepositoryHope this was useful and please do post any questions or comments.

Hi all,I would like to use Quantum DXi V5000 as deduplication storage appliance  Unfortunately, when adding deduplication storage appliance, there is an error message, that there is no Veeam Data Mover service enabled on the virtual storage appliance To enable Veeam Data Mover service I need to install Veeam Data Mover on the appliance…. The issue is that I do not know default root password for Quantum DXi V5000 and adding non-root user to sudoers file didnt help.Is there any option to manually install Veeam Data Mover on linux based machine? 

 Extracted from original blog at wcithipster.com on Dec 2 Written By Zane AllynManaging datacenters is no small feat. From ensuring backups are reliable to monitoring virtual environments for potential issues, the demands on IT professionals are relentless. During my time as a Veeam customer and datacenter manager, Veeam One was my go-to tool for maintaining visibility and control. It wasn’t just a monitoring solution; it was an operational ally, helping my team and me proactively address challenges, optimize resources, and deliver consistent performance across our environments.Now, with the release of Veeam One V13, the tool I once relied on extensively has been reimagined to make monitoring and reporting even more intuitive, powerful, and accessible. From a brand-new web interface to advanced features like agent-based data collection and deployment modeling, this latest version raises the bar for what IT teams can achieve. Whether you're managing a sprawling virtual infrastructure or

Good morning. I usually perform backup jobs using the Oracle RMAN plugin for a primary repository.When creating a copy job of this backup job for a second repository, I receive several errors saying "File does not exist. File: [XXXX.vab].Where is Veeam looking for these files that no longer exist in the primary repository?We have an immutability configuration of 30 days in our primary repository. Since this is our first contact with Veeam, we were mistakenly deleting Oracle RMAN backup files older than 30 days directly in the repository file system. However, we were instructed by Veeam support to just rescan the repository so that possible invalid files in the Veeam database catalog could be resynchronized, but this did not solve the problem.I have an open case about this but still no response. Has anyone had this problem and solved it?

 Hello.Tell me, is veeam backup version 11 installed, ASP NET and NETCore version 3 installed, how can I update the NET versions, does veeam backup 11 support newer NET versions.

I have one Windows physical endpoint which has the Veeam agent installed, and a backup is taken to the BackipRepository1 every few hours. I also need to take a backup of that machine once a week (midnight on Saturday) and retain 52 copies, but those backups need to go to BackupRepository2.I have tried to create the second job but get the following message.Skipping WINWORK0256548; workstation is already assigned to the backup policy Workstation1 Nothing to process. Failed to apply backup job configuration at date and timeIs there a way for me to have two different backup jobs for a single endpoint like this, please?

This is part 2 of the blog series about Veeam Backup for Proxmox, which focuses on backup and restore. Part 1 was about the architecture and setup; in case you’ve missed it, you can find it here: Disclaimer: All information and screenshots in this blog post are based on an early access release. Until the final release changes can and will occur! Restoring/Migrating from VMwareBefore we can start to backup systems running on Proxmox, of course we need to deploy a VM. The first release of Veeam Backup for Proxmox will support cross-platform restore, so I restored an existing Windows Server 2022 system from VMware to Proxmox.The process isn’t much different from other platforms and doesn’t require any special knowledge.   In the storage tab, you need to select the destination storage/datastore and define which type of disk (RAW, QCOW2, VMDK) shall be used.  After the restore completed, I noticed that the BIOS was set to “SeaBIOS” by default. As Windows Server 2022 required UEFI to boot, I

Hello everyone. Last time we explored how to identify basic file Indicators of Compromise (IoCs), develop YARA rules to detect malicious actors, and incorporate these rules into Veeam Backup & Replication to identify potential malware in our backups.Taking it a step further, today we will explore how to automatically generate YARA rules using YarGen. YarGenYarGen is a tool that generates YARA rules from a specified malware file. It identifies unique strings within the malware and excludes those prevalent in non-malicious files. This is achieved using YarGen's comprehensive database of strings and opcodes typically found in non-malicious files. Essentially, it creates YARA rules from strings in malware files while discarding those also present in goodware files.There are many variable and options that can be set in YarGen, today we are going to look at how it can create a YARA rule based off of a potential malware file. Back to basics - IoCSA user has noticed a folder called “freest

Missing application permissions: Exchange.ManageAsApp. Public folder and discovery search mailboxes will be skipped from processing, and a shared mailbox type will not be identified.I have a fully licensed version of Veeam Backup for Microsoft 365 (not the community edition) which I recently upgradded to version 8.1.  Since then I’m getting this message.  I tried to put in a support ticket but that doesn’t work so I thought I’d try here.I have already followed the instructions on https://helpcenter.veeam.com/docs/vbo365/guide/ad_app_permissions_sd.html?ver=80 where I assigned Global Reader to the Veeam App ID but I still get the error message.Useful suggestions gratefully received.

I’d like to gather as much information on hardening Windows Repos and Proxies, and have it all posted below to help others if they are looking for information on this topic.We all know the Veeam B&R Server has a security checklist which gives you very clear concise things to do for security.  There is also the LHR.  Following the DISA STIG, or using the ISO is a great way to make sure the software portion of your LHR is safe.With the above, you still have to protect the underlying hardware. Everything from physically getting at the Disk, Server Bios/UEFI, destroying the hardware, to SSH ports on a SAN, and use of MFA for logins to a SAN to prevent access. Turning on immutable snapshots and 4-eyes features on the storage pools are also great to implement. Lets not forget the VLAN for your management networks and who is allowed to see those IP’s. Even with all of this, I still don’t see specific documents for hardening a Windows Repository or Proxy server. Many of the same guidelines

I am working on a deployment of Veeam 12.3 on Windows Server 2025 as I see there is now official support.  I am planning to use PostgreSQL, and I was wondering which version to choose.  The 12.3 ISO comes with v15.10-1.  Is that Veeam’s recommendation for Server 2025?The latest version of PostgreSQL is 17.2.  Try as I might, I can’t find any statements regarding PostgreSQL’s support for Windows Server 2025, but if Veeam support is willing to stand behind it, that’s good enough for me.Also, am I correct to assume the only way to run the DB on its own drive (D:) is a manual install of PostgreSQL before the Veeam install?

Hello All,I'm testing Veeam with my homelab Proxmox cluster. I have an issue with a worker on a node that is not reachable every other day. The backup gives a warning message. When I test the worker in the Veeam console I'm getting this message <<<<<<19/01/2025 20:42:53 Error Failed to synchronize configuration settings of the worker XXX-worker can't lock file '/var/lock/qemu-server/lock-101.conf' - got timeout19/01/2025 20:42:53 Error Worker XXXworker test failed: can't lock file '/var/lock/qemu-server/lock-101.conf' - got timeoutHere is the warning message from the emailFailed to prepare the worker XXX-worker: Failed to power on the worker VM: Failed to wait for the task UPID:XXX:0006259E:0080C27A:678CCD30:qmstart:101:root@pam: to complete; There are no available workers in the cluster. Performance may be affected; Failed to prepare the worker worker: Failed to power on the worker VM: storage 'datastore' does not exist; Job finished with warning at 1/19/2025 1:25:27

I am trying this one more time and have had this work in the past but just wasted hours on a restore that would not boot. I have a replacement laptop a little newer and I installed veeam on the new laptop and created the usb drive. I then booted the usb and went into bare metal selected, connected to my veeam backup and recovery and selected the restore point, removed the partitions and did the restore. The restore said it completed successfully but would not boot even with secure boot off. Tried start up repair and unable to repair. I selected command prompt and I could see all of the files were there and tried some bcdrec stuff but nothing worked. I can restore a clean image and then restore my files that way but the bare metal recovery is supposed to work and obviously it is not in my case. Currently running endpoint backup version 6.2. Trying again but pretty sure it will give me the same result.

Enhancing Your Veeam Security: Key Features to ActivateVeeam Software’s R&D department has been busy the past year. It has introduced three minor feature releases (V12.1, 12.2, and 12.3), including crucial new security features and updates. If you have just installed V12 or are still on V11 and are planning an upgrade to the latest V12 release (V12.3), you may be overwhelmed by figuring out an “order of importance” for activating features.I suggest to customers moving to V12.3, or are using V12.3 but haven’t implemented any security features yet to turn on the new features in this order: Veeam Hardened repository, MFA, 4-Eyes authorization, Entropy and Indicators of Compromise scanning, and Veeam Threat Hunter. First: Veeam Hardened repositoryThe security of your backup infrastructure should start with and center around Immutable storage.  For Veeam, this is the Veeam Hardened Repository (VHR). The Veeam Hardened Repository is delivered as a bootable ISO. It allows you to create a

Hello everyone,A customer of mine wants to restore the SQL backup taken on the VBR Server on a different server. There is no problem so far, but it wants to make the TCP - 1433, 1434 ports 1435 ports required in SQL Restore. Can he do this? If so, does anyone have information on how to do it?

I did a Volume restore a few minutes ago, rolling back to last night’s backup. This is a windows server 2019 environment; NTFS; prior to the restore, I had a couple dozen volume shadow copy restore points. The last one was 5pm yesterday; the nightly backup runs at 11PM. My office manger was working past 5pm, so I was forced to use the volume restore.When the restore was complete, there are no VSC restore points available. Not a big deal in this instance, but they are supposed to be there, correct? Did I do something wrong? Any ideas? 

Hi i have a PC that was being backed up wit veeam agent for windows free edition not managed by VBRThe PC is runing windows 10 22H2 ,After an agent update started getting the error failed to start service "VeeamEndpointBackupSvc"Tried repairing the agent , i tried removing it and reinstalling it still getting the same error .It seems something with the agent setting is wrong and removing the agent doesn't really clean all the data from the PC , tried even installing older version still the same.Also i am not seeing that service registered in services Any ideas how to purge the data ?  Or Fix this issue ?Thanks